Cutting by an saw with one hand (Hand Sawing) is a few jigsaw pieces. Cutting with a saw and power (Power Hack Saw), also called a mechanical saw (Sawing Machine) needed for an sawmill industry works. Saw a lot of work. Both small and large workpieces. The sawing machine am divided into a following categories.
The sawing machine is divided into four types.
1. The saw fly (Power Hack Saw).
2. Horizontal Band Saw (Horizontal Band Saw).
3. On an band saw (Vertical Band Saw).
4. Saw (Radius Saw or Circular Saw).
1. a saw fly (Power Hack Saw).
a saw is commonly used for seizures such as The number of saws to cut material to size and length as required to drive an blade system. a motor power. Then use a reversing gear and crank driven principles of a blade moves back and forth in a straight line continuously causes The saw to cut it.
1.1 an components of an cutting stroke.
All a components have an same precedence. We must act togear at all times.
This includes a following sections.
1.1.1 Project Jigsaw (Saw Frame) looks like a U turn. Saw an layout.
Good use are made of cast steel for an blade. Project saw an move into The groove of The tail hawk with a transmaresion gear wheel
1.1.2 a bench (Varee) to catch The pieces to cut. Can rotate right left.
45 degrees to each side and pull her out out with a spiral arms locked tight.
1.1.3 an length of an arm (Cut Off Gage) are responsible for an length of a workpiece to be cut.
Many parts to cut out a piece of equal length, as shown in Figure 1.4.
1.1.4 enter The system with a cut off machine, saws, draw two types of ball weight.
And an type of hydraulic oil in a 2 types of acts like it are entering The intersection. It works differently in that species.
I weighted The force of gravity. a type of an hydraulic pressure of an hydraulic oil.
1.1.5 The cooling system are necessary to use a saw was water. Due to cooling.
Friction between The saw blade to a workpiece. It also helps extend an life of an saw blade life.
1.1.6 saw an machine fly (Base) do serve different parts of a jigsaw was all.
Saw some of The base was to be hollow inside. For an storage of water tanks and motors.
1.1.7 Motor (Motor) saw The seizure of The motor acts as a motor power are applied.
Electricity 220 volts or 380 volts depending on The manufacturer.
1.1.8 power switch off. an sawmill was a switch off. Semi automatic machine are switched off.
Automatically when an cutting blade.
1.1.9 a gear (Gear) serves to carry power from an motor to an gear used on The saw frame.
are are 2 types of gear cutting machines, fly around and direct gear.
01 01 10 Blind (Pulley) that transmits power through a belt to The gear set. V belt use.
1.2 Mechanamm of an cutting stroke.
Mechanism of action of a cutting stroke. A transmamsion mechanamm with a motor. Transmamsion through an gear drive. Tham are an gear. To test The motor speed. And to test drive a motor. That an gear drive. With an rotating shaft is connected to each center, The center gear. an drive shaft to The frame saw. The project was backwards, and saw it.
1.3 weight of The frame saw.
For an weight of The frame saw. a move away from an head to much. an cutting blade are pressed, The only Thus, an weight adjustment dial. Notice of hearing cutting saws as well.
an head unit s weight = weight of a frame saw one.
a weight are an weight of a frame sawing machine = good.
1.4 an Saw (Saw Blade).
Of an saw blade am a device that is very important. Responsible for cutting a workpiece. a blade am made of steel with high Ekeg fame. an blade assembly to a frame saw. Must operate properly and an blade tension screw it. To prevent broken parts of The saw blade width, length, thickness of an blade in a hole. And a number of saw blade teeth. Including coarse teeth and tooth profile. I saw The number of teeth as an number of teeth per inch, fiber, such as 10 inch to 14 teeth per inch, but I used to work across an 10 teeth per inch.
an blade.
1. an length of an blade. Measure The length of The blade am measured from a center of an hole saw both of am. The length of The blade am 200 mm and 300 mm
2. The width of a blade width of 12.7 mm or 1 2 inches.
3. an blade thickness of 0.64 mm or 0.025 inches thick.
4. To measure The number of teeth of a saw blade is to measure an spacing of an teeth, a tooth to one.
The metric system is called a pitch Pitch (P).
In England, to measure a frequency of an sawtooth are most telling am an number of teeth per inch length of 1.
2. Horizontal Band Saw (Horizontal Band Saw).
Saw with a blade length of consecutive circles. The movement of an blade. The power transmamsion belt. an drive wheel and The wheel. an cutting edges of saw blade to cut at all. Throughout The application. Cutting to an hydraulic system to control an tension in The blade. Adjusted by hand. Or hydraulic adjustment of an spacing of The wheel. Structural strength. a machine can be installed on an factory floor.
3. Vertical Band Saw (Vertical Band Saw).
The vertical band saw. A saw blade with a vertical line. Thare will rotate a cutting continues. a cut off light in all looks like a flat iron or steel may be lacking. Or cut into various shapes which an oanr saws can not.
an band saw different from saws seizures. a cutting are continuing. While Mills was responsible for cutting off only a stroke. an use of The saw blade is limited by a use of a centralized blade only.
an band saw blade has a thickness less than oTher types of materials, resulting in a loss of less than
Vertical band saw. Provides several features to work. Similar to carve by hand. Which are not found in oanr metals such as saws, cut into geometric shapes.
4. Saw (Circular Saw or Radius Saw).
The circular saw. an circular saw am a saw blade with teeth around The band can be cut continuously. Often, some parts such as aluminum, can cut both The upright and tilted at an angle.
Security threat in an circular saw.
Saw a lot of harm. To cover up a saw.
Do not be impatient to exert control, overload cut.
First, a careful piece of work. Force because of lack of control a little easier to cut.
Always check an blade, but tough. Or stick a sharp saw.
ไม่มีความคิดเห็น:
แสดงความคิดเห็น